Mandarin Garden in Berkeley, CA *****

This restaurant has the absolutely the most delicious Peking duck! I say, visit the place for the duck itself. It’s definitely worth driving a few miles for. They come with tortilla like wrapping paper instead of your typical bread – the skin is crispy and meat is juicy. In the bread, we put some hoisin sauce and cucumbers and green onions along with the meat/skin. The waiter was nice enough to give us a demonstration as well. The staff is very friendly and can speak Chinese, Japanese and English.

Aside from the duck, we’ve had other items on the menu that were quite good. I really liked the pot stickers and they seem to have a specialty called stuffed eggplants that other restaurants don’t seem to carry.

I’ll definitely visit the restaurant again should I be in Berkeley.

lost vmfs volume – says 100% available – SAN LUN, storage pr

1) fdisk -l

this would show which device doesn’t have a partition.

2) dd if=/dev/sd(x) of=/tmp/dump_sdx.txt count=100 bs=1024

file /tmp/dump_sdx.txt shows x86 boot sector.

strings /tmp/dump_sdx.txt shows some vmdk files

3) fdisk -lu /dev/sd(x) shows that there are no partitions on the disk.

4) ran fdisk /dev/sd(x). created new partition spanning entire lun and then used partition type fb.

5) run “vmkfstools -V”

That’s it

NTP notes

http://www.cisl.ucar.edu/nets/intro/sta … s/ntp.html NTP (Pete’s notes) To get ntpd working, get a version that’s at or later than
ntp-stable-4.2.0a-20040617. Gunzip it, untar it, run ./configure,
make and make install. I couldn’t RPM-delete the ntp that’s
installed, so I hand-deleted all the ntp* binaries in
/usr/sbin. I know this isn’t optimal. Then I
hand-edited the /etc/init.d/ntpd, deleted the
/etc/sysconfig/ntpd, and made
/etc/sysconfig/iptables allow ntp packets. Then
I edited /etc/ntp/conf to camment out all the
lines except restrict 128.117.0.0 mask 255.255.0.0
disable auth
broadcastclient
I did
/etc/init.d/ntpd stop
/etc/init.d/ntpd start
,,,and waited a few minutes for the router’s broadcast packets to
be heard. Then I did ntpq and “peers” and saw the router listed.
One other possible problem: if your machine’s time is too far
out of sync with the router’s, ntpd won’t correct it. To force
synchronization, do “ntpdate mlra”.
The ntp.conf file has a section that configures
a fake driver. If you leave that on, you’ll see the “LOCAL”
peer. When you comment it out, ntpq “peers” will give
“No

How to build redhat kernel for VMware for time issue

Anyways, here’s how you do it:
1) download kernel source. I got mine from:
ftp://ftp.redhat.com/pub/redhat/linux/u … EL.src.rpm 2) install source:
rpm -i kernel-2.6.9-34.0.2.EL.src.rpm
(You may need to run “mkdir -p /usr/src/redhat/SOURCES”. If that’s the case, then I’d run “mkdir -p /usr/src/redhat/SOURCES /usr/src/redhat/SPEC /usr/src/redhat/RPMS /usr/src/redhat/SRPMS /usr/src/redhat/BUILD” just in case. ) 3) edit files to include BusLogic driver:
cd /usr/src/redhat/SOURCES edit the following files:
kernel-2.6.9-i686.config
kernel-2.6.9-i686-hugemem.config
kernel-2.6.9-i686-smp.config replace all instances of:
# CONFIG_SCSI_BUSLOGIC is not set
with:
CONFIG_SCSI_BUSLOGIC=m 4) make a patch change the Internal kernel timer frequency.
cd /usr/src/redhat/SOURCES
tar jxvf linux-2.6.9.tar.bz2
mkdir -p linux-2.6.9-vmware/include/asm-i386
cp -pr linux-2.6.9/include/asm-i386/param.h linux-2.6.9-vmware/include/asm-i386/param.h
open linux-2.6.9-vmware/include/asm-i386/param.h
change
# define HZ 1000 /* Internal kernel timer frequency */
to
# define HZ 100 /* Internal kernel timer frequency */ diff -urN linux-2.6.9/include/asm-i386/param.h linux-2.6.9-vmware/include/asm-i386/param.h > vmware.patch add the patch to the spec file list
open /usr/src/redhat/SPECS/kernel-2.6.spec
added to where it lists the patches (your numbers may vary):
I just made it Patch 5 since it doesn’t exist:
so after the line: Patch4: linux-2.6.9-selected-ac-bits.patch
Patch5: vmware.patch and where it does the prep after the line: %patch4 -p1
%patch5 -p1 5) change the release of your kernel to differentiate:
cd /usr/src/redhat/SPECS
open the file: kernel-2.6.spec and change:
%define release 34.0.2.EL
to
%define release 34.0.2.EL.vmware 6) build the rpm.
rpmbuild -ba –target=i686 /usr/src/redhat/SPECS/kernel-2.6.spec You could use
rpmbuild -bb –target=i686 /usr/src/redhat/SPECS/kernel-2.6.spec
if you only need the binary rpms, but since we modified the source, I like to use ba, so I can reuse the source rpm should I need to compile again.]]>

Buslogic driver for RHEL4 update4 (2.6.9-39 kernel)

For the update4 (20060605) distro, the kernel version is 2.6.9-39, so the buslogic driver on VMware’s site doesn’t work anymore. You can use the one attached, but it’s not supported by VMware. Install Linux by following the instructions on their site.

This is obviously not supported by VMware, Inc. There’s also no guarantee that your VM will be stable, but I’d bet that it would be.

ESX 3.0 cdrom problem – won’t mount / won’t work for Guest

[[email protected] root]# mount /dev/cdrom /mnt/cdrom/
mount: /dev/cdrom: can’t read superblock from /var.log/messages
Apr 27 09:40:06 wesx3 modprobe: modprobe: Can’t locate module ide-cd Fix with the following:
1) remove the line from /etc/vmware/esx.conf by running:
nano /boot/kernelAppend = “hda=ide-scsi”
2) remove hda=ide-scsi from /etc/grub.conf using nano again:
nano /etc/grub.conf
3) reboot the machine. That’s it!]]>